新闻动态
水泥免烧砖机模具空心砖模具的使用和维护
水泥免烧砖机模具空心砖模具制作精度高、难度大、生产周期长,配套和合理使用模具是用户购机之前就要综合考虑的要点,从安装、使用开始,请用户根据客户提供的图纸审查各种模具。
The hollow brick mould of cement unburned brick machine is of high precision, great difficulty and long production cycle. The key points to be considered before purchasing the machine are matching and rational use of the mould. From the beginning of installation and use, users are invited to examine the various moulds according to the drawings provided by customers.
1.安装或更换新、旧模具,一定要避免冲撞、磕碰,文明装配,注意保护模具。
1. Installation or replacement of new and old moulds, we must avoid collision, knock, civilized assembly, pay attention to the protection of moulds.
2.使用中经常检查模具尺寸,焊接结合部位状况,出现焊缝裂纹,应及时修补,出现磨损过快要调整骨料粒度,磨损过度影响制品质量需另配新模具.
2. Always check the size of the die, the condition of the welding joint and the crack of the weld seam in use. It should be repaired in time. If the abrasion occurs too fast, the aggregate size should be adjusted. If the abrasion excessively affects the quality of the product, a new die should be added.
3认真调节间隙,包括压头与模芯、压头与料车运动平面、模框与线板等间距,相对运动不得干涉,搽碰。
3 carefully adjust the clearance, including the distance between the press head and the die core, the moving plane between the press head and the feeder, the die frame and the wire plate, and the relative movement should not interfere and touch.
4.日常清理模具是,使用空压机、软性工具清楚混凝土残渣,严禁重力敲打、撬刮模具。
4. Daily cleaning of moulds is to use air compressors and soft tools to clear the concrete residue, and strictly prohibit gravity beating and scraping moulds.
5.替换下来的模具,清洗干净,涂油防锈,应置干燥、平整处支垫平放,防止重力变形。
5. Replaced moulds should be cleaned, oiled and rust-proof. Pads should be laid flat at dry and flat places to prevent gravity deformation.
The hollow brick mould of cement unburned brick machine is of high precision, great difficulty and long production cycle. The key points to be considered before purchasing the machine are matching and rational use of the mould. From the beginning of installation and use, users are invited to examine the various moulds according to the drawings provided by customers.
1.安装或更换新、旧模具,一定要避免冲撞、磕碰,文明装配,注意保护模具。
1. Installation or replacement of new and old moulds, we must avoid collision, knock, civilized assembly, pay attention to the protection of moulds.
2.使用中经常检查模具尺寸,焊接结合部位状况,出现焊缝裂纹,应及时修补,出现磨损过快要调整骨料粒度,磨损过度影响制品质量需另配新模具.
2. Always check the size of the die, the condition of the welding joint and the crack of the weld seam in use. It should be repaired in time. If the abrasion occurs too fast, the aggregate size should be adjusted. If the abrasion excessively affects the quality of the product, a new die should be added.
3认真调节间隙,包括压头与模芯、压头与料车运动平面、模框与线板等间距,相对运动不得干涉,搽碰。
3 carefully adjust the clearance, including the distance between the press head and the die core, the moving plane between the press head and the feeder, the die frame and the wire plate, and the relative movement should not interfere and touch.
4.日常清理模具是,使用空压机、软性工具清楚混凝土残渣,严禁重力敲打、撬刮模具。
4. Daily cleaning of moulds is to use air compressors and soft tools to clear the concrete residue, and strictly prohibit gravity beating and scraping moulds.
5.替换下来的模具,清洗干净,涂油防锈,应置干燥、平整处支垫平放,防止重力变形。
5. Replaced moulds should be cleaned, oiled and rust-proof. Pads should be laid flat at dry and flat places to prevent gravity deformation.
